wallyandsue.blogspot.com
Wally&Sue: bolt lock tabs and zerk for steering intermediate shaft
http://wallyandsue.blogspot.com/2015/05/bolt-lock-tabs-and-zerk-for-steering.html
Friday, May 29, 2015. Bolt lock tabs and zerk for steering intermediate shaft. The boots had deteriorated on our GMC's intermediate shaft. The bolt lock tabs didn't live through the disassembly so new ones got made. Good use for a abandoned realtor sign. Put in a zerk too. Subscribe to: Post Comments (Atom). Bolt lock tabs and zerk for steering intermediate . Spare hydroboost with matching input rod. Megasquirt port injection project pics. GMC Motor Home Photosite. Jon Roche Web Blog. A Sadly Glorious Day.
wallyandsue.blogspot.com
Wally&Sue: Lambke style caliper mounts
http://wallyandsue.blogspot.com/2015/03/lambke-style-caliper-mounts.html
Tuesday, March 10, 2015. Lambke style caliper mounts. Universal plates from Manny's Transmission to make fit D52 GM calipers and Lambke style forked mounts. Measuring hole location on knuckle. Making a two axis fixture plate to run in the lathe. Bevelled for penetration, not a lot of clearance for the threaded hole that's not there yet. Slotting two at a time. Making a drilling jig. Alignment bar bolted on. Drilling for caliper pins. Tapping caliper pin holes. 1976 Eldorado park brake caliper test fit.
wallyandsue.blogspot.com
Wally&Sue: April 2015
http://wallyandsue.blogspot.com/2015_04_01_archive.html
Saturday, April 4, 2015. J&S Safeguard pulls timing. High coolant temp makes it knock a little.Cant hear any of these, usually no activity on these. Going up hill on cruise control then lean cruise at the top on the flat. Left gage is J&S safeguard pulling timing on individual cylinders and adding it back. LED between gages is Megasquirt pulling timing on all cylinders and adding it back when it goes to a different place on the ve table. Right gage is air fuel ratio. Http:/ www.jandssafeguard.com/. Megas...
wallyandsue.blogspot.com
Wally&Sue: June 2015
http://wallyandsue.blogspot.com/2015_06_01_archive.html
Sunday, June 28, 2015. P 30 master cylinder bench bleed and install. Chevrolet's 1992 P model service manual has the master cylinder bench bleeding procedure using plugs on the ports. Position the master with the front slightly down, push the piston with short 1 inch strokes until resistance and no bubbles. Then reposition with the front slightly up and push the piston until no bubbles. I made a contraption that fits in a vise to do this. Monday, June 22, 2015. P 30 master cylinder gets a sight glass.
wallyandsue.blogspot.com
Wally&Sue: spare hydroboost with matching input rod
http://wallyandsue.blogspot.com/2015/05/spare-hydroboost-with-matching-input-rod.html
Monday, May 4, 2015. Spare hydroboost with matching input rod. Making a spare hydroboost with a matching input rod. Cut and threaded the rod to make a matching length booster to eye dimension. Eye was made out of cold rolled round steel. Slug matches drilled hole angle and fits in the bottom of the hole that's not threaded. Load is on slug and not threads this way. Subscribe to: Post Comments (Atom). Bolt lock tabs and zerk for steering intermediate . Spare hydroboost with matching input rod. Self levell...
wallyandsue.blogspot.com
Wally&Sue: Tree 2UVR-C rapid
http://wallyandsue.blogspot.com/2015/05/tree-2uvr-c-rapid.html
Friday, May 29, 2015. 750 HSS 4 flute end mill, mild steel, 300 rpm, 100% doc, .060 step over, 2.4 ipm. Rapid feed over runs a ratchet clutch. Interesting sound I think. Subscribe to: Post Comments (Atom). Bolt lock tabs and zerk for steering intermediate . Spare hydroboost with matching input rod. Megasquirt port injection project pics. GMC Motor Home Photosite. Jon Roche Web Blog. Rear Flexsteel seat Mount pictures. Neon's Glow - The Blog of John DeArmond. A Sadly Glorious Day. View my complete profile.
wallyandsue.blogspot.com
Wally&Sue: Rotor mods
http://wallyandsue.blogspot.com/2015/06/rotor-mods.html
Wednesday, June 17, 2015. Labels: Brake rotor modification. Subscribe to: Post Comments (Atom). P 30 master cylinder bench bleed and install. P 30 master cylinder gets a sight glass. Lambke caliper mount fabrication. Megasquirt port injection project pics. GMC Motor Home Photosite. Jon Roche Web Blog. Rear Flexsteel seat Mount pictures. Neon's Glow - The Blog of John DeArmond. A Sadly Glorious Day. Sue and I get to travel with our GMC motorhome. The GMC is a hobby we both can use. View my complete profile.
wallyandsue.blogspot.com
Wally&Sue: Ancient DuoTherm heat strip and dehumidify mod
http://wallyandsue.blogspot.com/2015/07/ancient-duotherm-heat-strip-and.html
Saturday, July 25, 2015. Ancient DuoTherm heat strip and dehumidify mod. Not listed to fit our aircon but it will by drilling a couple holes. All of this can be done from the bottom no need to go on the roof. Element installed, two holes need drilled and some trimming on the screen. Grainger 5Z484 relay with pigtails soldered on 120vac coil 15 amp SPDT. Any like rated relay would work. This was Ebay 10$ and will fit in the electrical box. Relay out of focus and in the box. Folded up ready to install.
wallyandsue.blogspot.com
Wally&Sue: P 30 master cylinder gets a sight glass
http://wallyandsue.blogspot.com/2015/06/p-30-master-cylinder-gets-sight-glass.html
Monday, June 22, 2015. P 30 master cylinder gets a sight glass. Sight glass for brake fluid level check without removing the lid. Put the top and bottom fluid holes at a 15 degree angle so they will be vertical with everything installed on the Bob Stone hydroboost. O rings seal the plate to the reservoir. Glasses are 34.5mm watch crystals 2mm thick. 8-32 button head stainless screws in tapped holes of the plate sealed with Loctite 620. Brass nuts hold it on. Subscribe to: Post Comments (Atom). Onan throt...
wallyandsue.blogspot.com
Wally&Sue: March 2015
http://wallyandsue.blogspot.com/2015_03_01_archive.html
Tuesday, March 10, 2015. Lambke style caliper mounts. Universal plates from Manny's Transmission to make fit D52 GM calipers and Lambke style forked mounts. Measuring hole location on knuckle. Making a two axis fixture plate to run in the lathe. Bevelled for penetration, not a lot of clearance for the threaded hole that's not there yet. Slotting two at a time. Making a drilling jig. Alignment bar bolted on. Drilling for caliper pins. Tapping caliper pin holes. 1976 Eldorado park brake caliper test fit.